Modules: The Glue That Holds Your Adhesive Melter Together

Modules, they are the most used product on your packaging line, yet so many operators don’t understand how they are constructed or when to replace them. Like an oil filter on your car, a hot melt module’s main job is to be the conduit for applying adhesive on your packages and should be replaced every 1,000 hours. Replacing a module is simple, and the part itself is fairly inexpensive, but not changing them out could lead to extremely expensive repercussions.

There are two different ways that hot melt can be pumped through the module. First, there is an air on, spring off module (AO/SC). This type of module is the most common in the packaging industry, and the easiest module type to replace. It works by the gun pumping air into the module, to open the flood gates and pump the adhesive through the nozzle, on to the packaging material. When the airflow stops, a spring inside the module closes the opening and stops the adhesive from flowing. The other type of module is an air open, air close (AO/AC). This is a less common type of module and patented by Nordson®. If your machine operates with an air open, air close module then the replacements will be more costly and harder to find. Essentially, this module operates with air pumping through the gun to open the flow of adhesive, and then uses an air intake from the side of the module to stop the flow of adhesive. Keep in mind, that if you operate using an air open, air close module, you can replace it with an air open, spring close module by bypassing the air intake line. However, you cannot run an air open, air close module on an air open, spring close gun.

O-rings are an important component on any module. These tiny ring-shaped seals keep your module from clogging up, increases the efficiency of your system and limits the downtime of your lines. When replacing modules on your guns, make sure that the o-rings are placed securely on the module. If they get clogged with glue, then your module will clog and become defective.

Another important point to note when learning about your module, is the type of nozzle it takes. Not all nozzles and modules are the same. For example, zero cavity modules come with an integrated nozzle seat which allows for a no drip, positive cut off of adhesive. Each zero cavity module needs to be ordered by diameter size. A standard H200 module, however, does not come with any nozzle. You need to order nozzle separately and they come in multiple orifice sizes.

For more information on modules and how they can help improve your packaging line efficiency, reach out to Universal Systems SE at (561) 272-5442 or sales@ussefl.com. You can also view all of our ProBilt® series modules by visiting the Hot Melt Modules section of our website.

Read More

The Difference Between a Glue Gun Head and Module

By far, the most commonly asked question we receive is – what is the difference between a glue gun and a module? A misconception that many packaging line buyers make is that when a module fails, you need to replace the entire gun. That is not true. In most cases, the modules attach to the gun and can be easily removed and replaced.

Below is a breakdown of the components that comprise a hot melt adhesive gun application system:

  1. Gun Head – this is the gun body that attaches to the packaging line and initiates the application of melted adhesive into the module. There are a variety of different style gun heads, ranging from 1 module to multi module capacities.
  2. Module – the module attaches to the gun head via two screws. Each gun applicator will come with modules, but these can be replaced regularly once they get clogged. The module is the conduit that applies the adhesive to the package.
  3. Nozzles (not always included when you purchase a gun) – at the end of every module is a nozzle. Most standard nozzles will screw on to the end of the module. The diameter of the nozzle will determine how much hot melt is applied to each package. Some modules, such as reduced cavity, zero cavity and ProBead’s, will come with an integrated nozzle seat attached. Replacement kits for these integrated nozzles are sold separately, instead of buying a brand-new module.

If you only need to replace the module, and not the entire gun applicator, make sure you check which type of module you need. Below is a list of the most common modules in use today.

If you have any questions on which items you may need, please reach out to a sales representative by either calling (561) 272-5442 or emailing sales@ussefl.com. We manufacture all products in the United States and are here to offer the best price possible to get your packaging line up and running as quickly as possible.

Read More