It is Usually Always a Clog
The most common reason for your hot glue system acting up is because of a clog. Clogs are common because you are working with glue, which is sticky and chars over time. Below are some of the most common technical calls we receive, with the solution…and you guessed it, it’s usually always a clog.
Pump is not pumping
There are several reasons as to why your pump can stop up. Honestly, it is usually dirty oily air in your shifter. However, when it is not your shifter it is usually a clog. If your shifter is running fine, but it sucked something up into the hydraulics of the pump, the pump shifter will be stopped in the top position, unable to shift down. That is because you probably have some char or debris in your hot glue reservoir and while pumping, you sucked something up into the ball check valve. You have now clogged up your pump and need to send it in for a flush and clean. Another potential issue could arise if your pump is running but sluggish. If your pump is running mush slower than it used to, it is probably because you haven’t changed out your tank filter and it is clogged. The tank filter is located on the side of the tank and filters all glue before it runs into the hoses. If that filter is not regularly changed (every 500 – 1500 hours depending on how clean your glue is) then that clog can cause pressure to back up into the tank and not allow your pump to run at full capacity.
Gun is not firing
If your gun is not firing at all, it is probably your solenoid valve. However, if your gun is firing every other time or randomly, it is probably due to a clog in your in-line filters. The in-line filters filter the glue from your hoses into your gun. These filters are there to help filter our char or debris that was missed by the tank filter or that has built up in the heated hose. If the filter screens are not changed regularly, they will get clogged up and not allow for your gun to fire properly. For example, if you need to increase air pressure in order for your gun to fire, it is probably the in-line filter clogged up. Another clog can happen in the gun manifold itself. Typically, this is only in multi-module guns. If you have a multi-module gun and the last module in the line is not firing, there is probably a clog in the manifold.
Module Drips
If your module is constantly dripping glue, then you have a clog in your module. This is most common in air open, spring close modules. A piece of char will get stuck in the seat and not allow the piston to seal tightly, causing the glue to drip out. A clogged module will need to be replaced with a new module.
Nozzle keeps clogging
This one is fairly straight-forward. If your nozzles keep clogging there are a few solutions. First, you can change out your in-line gun filters. They are probably not clean and not filtering the glue through the gun. You can also increase your nozzle diameter. If you are running small hole nozzles such as .010 or .012 diameter, try a .014 or .016 and you will start to see less clogging. However, that will lay down a little more glue, so keep that in mind when reviewing your glue usage.
The best way overall to reduce the number of clogs in your hot melt systems is to do preventative maintenance. That means cleaning your tank every month or every quarter, depending on how many shifts your tanks are running. Universal Systems makes Purge Plus tank cleaner and we sell them in a 5-gallon pail so that you are set for at least 2 – 3 cleanings. Additionally, change out your tank filters and in-line filters. These 3 tips are the most inexpensive way to keep your hot melt system running smoothly.
How Dirty Air Impacts Your Pneumatic Systems
Pneumatic hot melt systems are run by air in both the pump and the applicator guns. One of the most important ways to ensure the longest run time out of any pneumatic system is to make sure that the air is clean and dry. That can be easier said than done. Most all packaging facilities have oil, water, or debris in their air. That is just the way it is. Some factories will install air cleaning systems and then add lubricators to lines to ensure that other equipment that requires oil runs smoothly. But even with the most expensive and elaborate air filtration system, there will always be some type of substance that gets by and can lead to issues in the pneumatic pumps of hot melt units. The simplest solution is to install an oil removal filter regulator to the air line running to the pump.
Oily air is our most commonly found issue inside facilities that have pumps stop up. The reason is because the shifters are manufactured with very specific tolerance clearance between the shifter spool and sleeve. This design is a necessity in order to get the pump to shift. Too much clearance and the air will just blow by the spool, never building up enough air pressure to pump. Too little clearance and the shifter will jam. That being said, if you have oily air or dirty air being run through the shifter, over time, that will cause a film to build up inside the shifter and cause a jam. Depending on the amount of oil or dirt in your air, and the number of hours the systems is run for, will determine how long this will take to happen. However, if you feel like your facility air is questionable, we suggest that you use the oil-removal filter regulator to prevent any shifter stop ups.
Another pump issue that can be caused by dirty or oily air is that it can get into the air motor and damage the rulon seals. The seals need to be tight to snuggly move up and down the air motor and if they get damaged by oil or dirt, that can lead to your pump not efficiently pumping. These seals can be replaced over time and should be checked every 2,000 hours.
Universal Systems offers pump rebuild kits for the seals, as well as sells the shifter valves in case you ever run into a pump issue caused by dirty, oily air. For more information on our pump rebuilding services, or for any technical support you might need, please call (561) 272-5542 or email sales@ussefl.com.
ProBilt Glue Systems Meet the Demands & Needs of Packaging Lines
The trend in packaging for many CPGs has been to move away from in-house packaging solutions and more towards co-packers and contract packagers. Rather than dedicating complete in-house lines, CPGs and processors can be more flexible with their budgets by putting the responsibility of capital investments for machinery in the hands of the contract packagers. In addition, the CPGs no longer have to worry about hiring line operators for the packaging machines. In the last few years, it has become clear that hiring, retaining and training employees is a challenge for every company. CPGs are finding that if they move the responsibility of packaging to contract companies, they no longer have to deal with that potential issue.
The move to contract packaging is not a bad thing for glue equipment OEMs, like Universal Systems SE. We enjoy working with contract packagers because they are equipped with the skills and knowledge to focus on packaging lines and, in most cases, know what they want and need from a hot glue machine, more than a CPG will.
Below is a list of requirements we are hearing about from Contract Packagers for their packaging equipment, and an explanation as to why Universal Systems ProBilt systems will work best to fulfill these needs.
- Quick changeovers to limit downtime – USSE’s ProBilt systems are plug and play. They are easy to set up and disable for cleaning, preventative maintenance, component replacement, etc.
- Preventative maintenance schedules – USSE believes that preventative maintenance is key to maintain the efficiency and longevity of any piece of machinery. A hot glue tank is no different. Universal Systems offers up a preventative maintenance schedule upon request, along with recommendations on what parts to keep on the shelf and how many of each part is needed to keep your operation up and running at all times.
- Streamlined equipment so that system components are interchangeable – Universal Systems prides ourselves in being the most streamlined OEM of hot melt machines in the market. Not only do all of our tanks take the same pumps, filters, valves, etc., all of our components are interchangeable with our top competitors including hoses, guns, modules and nozzles.
- Versatility for different packaging setups – Universal Systems manufactures over 100 different types of applications options, as well as the option to custom CNC any configuration needed.
- Easy-to-operate machines – Our ProBilt tanks are by far the easiest in the industry to operate. We focus on longevity and simplicity so that anyone can set up and operate our tanks with ease. We also offer online videos on how to set temperature and utilize our setback feature.
For more information on Universal Systems and our ProBilt line of products please reach out to sales@ussefl.com or call (561) 272-5442.
How to Change Out a Melter Pump
There are several reasons why a melter’s pump might stop working. The most common reasons are clogging of the ball and seat from foreign matter such as carton dust, and the actuator clogging due to dirty or oily air. No matter what the reason, if your pump stops pumping it needs to be replaced. Obviously, it much more cost effective to change out a pump then to replace the entire unit. However, it is not always easy to switch out a pump, especially if you are new to the line. Below are a few tips to help ease you through the process.
- Make sure the circuit breaker on the front of the unit is set to OFF once the applicator has reached normal application temperature.
- Shut OFF the input air to the pump.
- Set the pump regulator to zero and trigger all guns to relieve system pressure.
- When removing the old pump, rotate it slightly to break the suction and then pull it straight up and out.
- When installing the new pump, make sure to torque the screws 15-16 ft-lbs.
- Connect the pump electrical plug to tank receptacle and turn tank back on.
- Once the tank board reads that the tank has reached set temperature, wait 15 minutes. This will allow the glue around the pump hydraulics to get to temperature.
- After waiting 15 minutes, reinstall the air regulator and connect the airline and activate air.
If you have any further technical questions and want to speak with a technical sales rep, please call (561) 272-5442 or email sales@ussefl.com.
The Importance of Product Support
Universal Systems SE has been manufacturing hot melt equipment since 1981. Starting with hoses and nozzles, then moving into applicators, pumps and tanks. Our first ProBilt tank was launched in 1990. Since then, our melter has only had a couple of generational upgrades. We believe that this is what sets us apart from other hot melt equipment manufacturers in the industry today. We have never believed upgrading our equipment or technology so much that it makes our old tanks in operation obsolete. We have added features and improved upon what we initially launched in 1990, but we have not let technology negatively impact the operational ease of our machines.
USSE believes in the importance of long-term product support and cross compatibility. There are hot melt system manufacturer’s in the industry, like Nordson®, who have discontinued not only production but also product support of their old melters. Both the 2300 series and 3000 series melters, while discontinued by Nordson®, are still in operation in hundreds of packaging facilities across America. Unlike Nordson®, Universal Systems still supports those old melters because we appreciate the fact that many of these melters, similar to the ProBilt melters, continue to run even 20+ years after initial operation. We are one of the only manufacturers in existence to still make and service 2300 & 3000 series pumps.
We also believe in product uniformity across all of our melters. That is why when we designed our melters, we made sure that all of Universal Systems’ ProBilt machines run the same control boards, pumps and tank filters. In most cases, facilities run several ProBilt melters, but only need to stock 1 or 2 of each spare part. That uniformity creates a streamlined and more simplistic inventory process.
As we move deeper into 2021 and our new normal continues to change, think about how the importance of long-term product support and a streamlined inventory process can help keep your packaging lines up and running. For more information about Universal Systems and our ProBilt line of melters please email sales@ussefl.com.
Safety in Switching Out Glue Equipment
The best way to keep your packaging line up and running as efficiently as possible is to do preventative maintenance. Here at Universal Systems SE, we have advocated for regular packaging line maintenance, including all of your glue melter equipment and components. However, it is not only important to know when to do maintenance, it is also important to know how to do that maintenance. There are more mistakes made in the switching out of glue equipment and components than you may think. Whether you are changing out a filter or switching a pump, there are steps to take in order to ensure a smooth transition, with the least amount of downtime. Here are a few tips on switching some of our ProBilt hot melt equipment products.
Tank Filters
First and foremost, it is important to know the model of your tank. Even though that sounds like standard knowledge, there are many tanks that look similar but have different tank capacities, pump types and filters. Once you know the tank model, you can look up if you need to replace the entire tank filter or if you can replace just the screen. On USSE’s ProBilt tanks, for example, you have the option to change only the tank screen. This allows you to save some money long term, while still maintaining your tank. It is recommended that you make the change while the tank is in setback and to wear Kevlar gloves so that you don’t burn yourself. The tank filter is located on the side of the tank. It can be removed with a flat head screw driver. Once the complete filter assembly is removed, there is a long screw that secures the screen to the assembly. Simply remove that screw, switch the screen, and replace the filter assembly. If you are changing out the tank screen, make sure that you do not damage the filter bung or o-rings when making the switch. Also, be careful, the glue inside the filter is HOT.
In-line Gun Filters
These are the easiest of filters on your glue line to change out. In most cases, the filters can be reordered in packs of 5. Locate where the filter is on the filter assembly body and use a wrench to loosen and remove. Kevlar gloves should be worn, as the outside of the filter will be hot and there will be glue on the filter you are removing. Simply put the new filter in place and tighten.
Modules
Usually modules are switched out because they are dripping or leaking. This is typically caused by either char or end of life of seat and piston. Switching out a module is fairly simple. Before taking off the old module and replacing with the new, make sure that the system is not running. Each replacement module comes with 2 o-rings and 2 screws. Place the o-rings on the back of the module and secure it on the gun applicator with the new screws.
If you are running an H200, zero cavity or reduced cavity module, there are rebuild kits available.
Pumps
Switching out a glue pump is the least common practice on a packaging line. However, this is also simpler than you would think. Most technicians think that in order to change out a pump, you need to turn the tank off and let the glue cool. That is not always the case. If you are running a ProBilt tank and have an experience technician, he can switch out the pump while the system is still on. First, make sure you are wearing Kevlar gloves because the system will be hot. Turn off the air running to the system, this will limit any injuries. Remove the 3 bolts holding in the pump, use needle-nose pliers and do this carefully. Put the old pump on a large piece of cardboard where the glue can drain, cool and harden. Carefully put the new pump in, secure it with the 3 bolts and turn back on the air.
For any other questions about tank maintenance, please contact one of Universal Systems’ experienced technicians at (561) 272-5442 or email tech@ussefl.com
The Importance of Graphite Seals & PTFE in Hot Melt Equipment
Graphite seals and PTFE are used in all of Universal Systems SE’s pumps and modules to increase the longevity and life of those products. But why? In order to understand how we can boast about the quality of our products, it is first important to understand the quality and reasoning behind using certain key components.
Graphite seals are used in both the pumps and modules to create a smooth seal for the piston to move seamlessly through. Below are a few bullet points that explain why this particular component is so important.
- Excellent heat resistance – up to 500°F – most all hot melt adhesive systems will heat up to 450°F, so even if a packaging line runs at the highest temperature allowed by the system, the graphite seals will remain unscathed.
- It has a medium to high pressure rating – the maximum operating pressure on any pump should not exceed 35 – 45 psi. The most common operating pressure is 20 – 25 psi. These seals are rated perfectly for this type of application.
- Excellent abrasion resistance – some packaging lines are not run with the cleanest adhesives, so utilizing graphite seals allows for any adverse environmental condition.
- Very resistant to chemicals – this allows the end user the ability to not only use multiple types of adhesives, but cleaners as well.
- Excellent extrusion resistance in severe conditions.
If you are interested in learning more about the components used to manufacture Universal Systems line of ProBilt™ equipment, please call (561) 272-5442 or email tech@ussefl.com.
How to Keep Old Melters Operable
Do you have an old series 2300 or 3000 melter that you are still using but need to find parts for? If you do, your packaging line is running a melter that is 15 – 20 years old. That means that your line operators are maintaining your packaging lines well and spending money in the right areas to keep efficiency and durability a priority. With that said, not everything will last forever. While you can probably keep the control panels of the 2300 or 3000 melter, some of the internal and exterior parts may need to be replaced. The reality is that Nordson® no longer supports these tanks. However, Universal Systems SE does. Universal Systems SE manufactures pumps, filters, hoses, guns, modules and nozzles that are compatible with your old melters.
Pneumatic Pumps
The first thing to go on your old melter, will most likely be your pump. Once that stops working, it will become very clear that your OEM no longer manufactures replacements for that part. So now you have to decide between purchasing a new melter from them for $15,000+, or trying to replace your pump. Universal Systems SE manufactures new series 2300 and 3000 pumps for a fraction of the price of a new Nordson® melter. Check out our full line of pneumatic pumps.
Actuator
If you have experience with rebuilding pumps, Universal Systems also manufactures the pump shifter and fork for the ProBilt™ series 2300 and 3000 pumps. This is another item you will not be able to find with the OEM because it has been discontinued.
Tank Filters
Since your series 2300 or 3000 melters have been operating on the line for so many years, your line operators probably change out the tank filters frequently. As the years have gone by, you may find it more difficult to find reasonably priced, or readily available tank filters. Universal Systems manufactures the tank filter assemblies, filter cores and filter screens to fit your series 2300 and 3000 melters.
Same Footprint
If you have gone through all of the steps to fix the problem with your old melter and find out that it is the control panel, which has been discontinued, Universal Systems SE has a solution for that as well. Our ProBilt™ melters have the same footprint and dimensions as your current series 2300 or 3000 melter. That means that your NEW ProBilt™ melter, that comes with a 10-year heater warranty, will fit right in where your old melter comes out.
For more information or to contact a technician that can help you troubleshoot issues with your old melter, call (561) 272-5442 or email sales@ussefl.com.
Melt Rate vs. Pump Rate
When purchasing a hot melt adhesive system, it is important to know your desired melt rate and pump rate. It is also important to understand the difference.
All Universal Systems SE ProBilt™ tanks are equipped with a 14:1 ratio pneumatic pump assembly. Pneumatic pumps are most common and have a maximum pump rate of 75 lbs. per hour. No matter what the tank capacity is, whether it is 12 lb., 15 ob., or 20 lb., the pump will max out at 75 lbs. If you need to pump more adhesive then that per hour, you will need to transition to a gear pump system with a larger tank capacity.
The melt rate is the rate at which the tank will melt the adhesive you put into the reservoir. This is where the tank capacity comes into play. Before moving forward with any hot melt adhesive system, first you need to understand how many pounds you need to melt per hour. The melt rate is dependent on how many hoses and gun applicators you are running and how many boxes are sealed per minute on your packaging line. The most common tank capacity is the 20 lb. (10 Liter) ProBilt™ 20, with a melt rate of 23 lbs. per hour. If you are only running one line with one hose and gun applicator, then you may only need the 15 lb. (7 Liter) Probilt™ 15 which melts 18 lbs. per hour.
A common misconception is that the on-demand autofill system, the ProBilt™ Phoenix, will have a larger melt rate and pump rate. That is incorrect. The tank capacity on any auto fill system is the same as a regular tank such as the ProBilt™ 20. However, the advantage to the auto fill is that the line operators will not have to watch the adhesive level in the tank as closely. The vacuum system connected to the tank will sense when the adhesive level is low and automatically fill the tank. This helps eliminate dry running and pumps will last longer. However, the pump rate on this system will still max out at 75 lbs. per hour.
For additional information about melt rate and pump rate on all of our ProBilt™ tanks, please call (561) 272-5442 or email sales@ussefl.com.
Piston Pump Troubleshooting
There are several things that can cause a piston pump to stop working. The most common reason is that it is clogged. Unfortunately, not all line operators take the time to close the lid on a glue tank. With a lot of carton dust in the air at any facility, this dust gets into the glue pot and melts in with the glue. When the pump shifter runs to pump the glue from the pot into the hose, that carton dust gathers around the pump which can cause it to seize. The simple solution to this is to make sure that all shift line operators are diligent about closing the tank covers, that’s why they are on there.
If carton dust is not your issue, and the pump fails, below are a few other possible causes and the corresponding solutions.
- Adhesive not sufficiently heated – check the tank temperature and required melt temperature of your adhesive and set accordingly.
- Inadequate or no input air to pump – increase the air pressure from the plant air supply and see if the pump will run.
- Dry running – when a tank drops below a certain adhesive level in the pot, the pump does not have enough glue to operate at full capacity. The glue that runs through the pump acts as a padding so that the shifter does not pound against the top and bottom of the pump itself. When that padding is less, the pounding shifter can cause damage to the magnets and create an issue with the shifter. The only solution to this is to get a new shifter and potentially invest in an auto fill on-demand system that fills the glue into the tank for you, leaving less pressure on the line operators to fill the pot.
- No Tank Screen or Clogged Tank Screen – the tank screen lives at the bottom of the tank and is the first line of defense against any foreign debris getting into the pump. Sometimes the tank screen gets removed or never cleaned. That can cause debris build up and seize your pump. It is easily cleaned by lifting out of the empty tank and then cleaning the tank with Purge Plus™.
- Clogged Tank Filter – the tank filter screws into the side of the tank and filters the glue after it leaves the tank. If the tank filter is clogged, then the adhesive will back up in the pump, causing the pump to seize.
- Pump solenoid is not on – if the tank is not within 35 degrees of the setpoint temperature on the control panel, the pump solenoid will not turn on. Check the setpoint temperature and make sure it is correct. If the setpoint temperature is correct and reading properly, then it might be a failed solenoid that needs to be replaced.
If you go through all of these troubleshooting steps and still have an issue with your pump, please call (561) 272-5442 or email sales@ussefl.com.