Mini Modules and Gun Applicators
Several Years ago, Nordson® introduced the MBII gun applicators and modules. Initially, the small module and applicator manifold was made for packaging lines that were designed with little room for glue application. Then, they started offering them in a low-profile design for case sealers. Over time, Nordson® started using MBII guns and modules as standard equipment on all of their packaging line set ups. Why? Even though it is not clear the need for the MBII in most standard application setups that have room for an H200, the price surely made it a much more profitable product in Nordson’s® arsenal. The MBII is more than double the price of a standard H200 module and gun applicator.
The key question to ask is, when do you need to use a MBII applicator versus a standard H200 applicator? Like we mentioned earlier, a MBII applicator is essential on packaging lines that have about half the space to fit an applicator than typical lines. Not only is the manifold about half the length and height of a standard H200 gun, the modules measure a mere 1” x 2” in size. Additionally, MBII applicators have the filter built into the manifold. This is a space saver because it eliminates the need for the in-line filter assembly off of the back of a standard gun into a hose. This allows for the MBII gun to attach directly to the hose and still be able to filter out all of the char and debris travelling through the hose and into the manifold. MBII guns also are air open, air close systems, so you can only run them if you have your line set up with two air lines running to the gun. MBII modules do still fit all of the standard H200 nozzle tips. So, even though you cannot use your standard H200 module on the MBII manifold, you can use all of your current stock nozzles.
If your new packaging line comes in with a MBII system installed, our recommendation is to measure the space where the applicator is mounted. If you have room for a standard H200 applicator and in-line filter assembly, you can always switch to a standard H200 set up. The only thing you will need to change out is the gun, filter assembly and solenoid. This will save you thousands of dollars in the future…but only if it fits.
For more information about the mini modules and applicators manufactured by Universal Systems SE, please visit https://www.ussefl.com/products/applicator-gun-heads/h201t-guns/#1544128561143-eeff57c6-9818.
Cold Weather Impacts to Your Hot Glue Melter
As we move into the holiday season, we also experience a change in the weather. In most places in the US, the winter months mean that the climate inside most packaging plants change. With that, line operators need to take that temperature change into consideration when working with hot glue machines on their packaging lines.
Hot melt consistency, heated hose and gun temperature consistency and glue stringing are all potential problems that maintenance managers can deal with during the winter months. One of the most important things to look at is where your packaging line is located within your facility. Most melters are located at the end of the line, which leaves them close to an exterior wall, door or window. The cold temperature outside could be impacting, not only the viscosity of your glue, but the heating time of your glue and its adhesion ability. Every time your line operator opens the fill door on the hot melt tank, the external air hits the existing glue and cools it off. Even if the lid on your tank is only open for a few minutes, that could impact not only the current glue in the tank reservoir, but the glue you are adding to the tank. If your glue pellets are colder than normal, it will take a longer amount of time to heat them.
Another important task would be to inspect your system setup for any cold joints. A cold joint would be any unnecessary extensions that you have added throughout the adhesive application process. Most cold joints are found on older machines that use larger sized extensions and filter housings. The more cold joints on the system, the more inconsistent the glue will heat and stay heated throughout the entire application process.
If your main problem is glue stringing in the colder months, an easy solution would be to shorten the distance from the nozzle tip to the top of the box. Limiting the amount of time the glue has to travel in the air will help to lessen the problem of stringing, which can cause a weakened seal on the box.
If you have any questions about how to reduce the impact of winter weather on your hot melt system, please reach out to a technical rep at sales@ussefl.com.
How to Choose the Best Applicator for your Packaging Line
Oftentimes, a packaging line comes with standard, one module applicator guns. While that is the most common applicator on the market, there are several other application options available.
When figuring out your packaging line configuration, it may become apparent that a standard one module applicator will not work for you. It really depends on what you are closing up with hot melt. Are you running a case sealer? What size and style boxes are you sealing? How many edges do you need to hit with the glue and how do they fold together in the line? All of these questions need to be addressed before purchasing an applicator.
To help out, below is a list of some other common case sealer applicators. All of these items are in stock and ready to ship!
Low Profile
Low profile guns are one of the most commonly used guns on cartoners. Here at Universal Systems SE, we manufacture two module and four module versions to allow for easy glue distribution on small to large box sizes. Their name comes from their unique gun body design which is angled on each side. The angled design sides allow for the box flaps to flawlessly close while the gun is applying the adhesive on to the boxes.
Multi-Module Applicators
If you are running a high-speed line creating cartons that have multiple folds, such as a Douglas case erector, you may want to consider installing multiple module applicators. Universal Systems SE manufacture 2 module, 3 module, 4 module and 5 module applicators. There are various lengths between centers for each model. We recommend that you review all gun specs on our website.
For any other questions you may have regarding purchasing a new gun for your application, please give us a call at (561) 272-5442. We are happy to help create the best and most efficient hot melt application system possible.
RTD Sensors
RTD Sensors (resistance temperature detectors) are used in hot melt packaging systems because of their precision in sensing and proportioning temperature. They consistently maintain a temperature control stability of +/- 1-degree Fahrenheit. With the ever-increasing price of adhesive, it is important that RTD sensors are used in all of Universal Systems’ hot melt hoses and glue applicators for steady adhesive application. When combined with USSE’s patented AccuScan™ solid-state control system, RTD sensors provide precise bead uniformity for all of our ProBilt™ applicators.
Since RTD sensors are so key to the adhesive application process, it is important to check them first whenever you notice glue inconsistencies. If you see that your glue bead is not sticking properly or getting clogged, it could be caused by inconsistent glue temperature. There are several causes of inconsistent glue temperature. For example, if your tank operators are opening the cover to add glue, that will cause a temperature change. RTDs control that process, by notifying the heater to turn on and run longer when those situations occur. If your RTD is weak, then the heater will not be able to maintain steady temperature. It is the easiest, most overlooked and one of the least expensive components in your application process, but is worth it’s weight in glue!
When it comes to understanding the components that make up your adhesive application system, we believe that knowledge is power. So, if you have any questions, or think that you may be having issues with your RTD sensor, do not hesitate to call Universal Systems at (800) 848-5018 to speak with one of our technicians. We can walk your line operator through testing RTD sensors and how to switch them out correctly and safely.
Custom Manifolds & Gun Applicators
There are not many manufacturers in the hot melt industry that have the ability to work with clients and create custom manifolds and gun applicators to fit their unique needs. Universal Systems SE has that ability and is willing to pair up our engineers with our client’s team to ensure that we manufacture the exact applicator needed for any job.
Over the last forty years, Universal Systems SE has manufactured an array of different custom manifolds and gun applicator systems for different types of industries. Not only can our custom gun manifolds distribute adhesive onto boxes in packaging lines, but they can be used for distributing make-up, candle gel, etc. Depending on the viscosity and melt rate of the substance needed to make the transfer, our custom manifolds and applicators will work with several different types of materials.
The custom manifold and gun process is simple. Contact one of Universal Systems SE’s customer service representatives, by either calling in to (561) 272-5442 or submitting a custom gun online form. You will then be connected with a USSE mechanical engineer. After all of the client’s needs are communicated with our engineering team and all questions answered, USSE will provide the customer with a custom manifold drawing for approval. The drawing will include dimensions of the manifold, spacing of modules, type of modules and all cordsets that are included and the location of those cordsets. Once the drawing is signed off on by the customer, we then manufacture the manifold body. After a vigorous quality control process, each custom manifold is inspected and tested to ensure all dimensions are correct and that the custom gun matches the approved drawing. Once the manifold passes all initial testing, modules are added and the custom gun is created and tested internally by two different QC Engineers. Once there is approval by both engineers, the final product is cleaned and ready for shipping.
The normal process for custom manufactured manifolds and completed guns is four to six weeks, with extra time potentially added in depending on customer turnaround time for drawing approvals.
If you are interested in learning more about the types of custom manifolds and gun applicators that Universal Systems SE can engineer for you, please call (561) 272-5442 or email sales@ussefl.com.
The Difference Between a Glue Gun Head and Module
By far, the most commonly asked question we receive is – what is the difference between a glue gun and a module? A misconception that many packaging line buyers make is that when a module fails, you need to replace the entire gun. That is not true. In most cases, the modules attach to the gun and can be easily removed and replaced.
Below is a breakdown of the components that comprise a hot melt adhesive gun application system:
- Gun Head – this is the gun body that attaches to the packaging line and initiates the application of melted adhesive into the module. There are a variety of different style gun heads, ranging from 1 module to multi module capacities.
- Module – the module attaches to the gun head via two screws. Each gun applicator will come with modules, but these can be replaced regularly once they get clogged. The module is the conduit that applies the adhesive to the package.
- Nozzles (not always included when you purchase a gun) – at the end of every module is a nozzle. Most standard nozzles will screw on to the end of the module. The diameter of the nozzle will determine how much hot melt is applied to each package. Some modules, such as reduced cavity, zero cavity and ProBead’s, will come with an integrated nozzle seat attached. Replacement kits for these integrated nozzles are sold separately, instead of buying a brand-new module.
If you only need to replace the module, and not the entire gun applicator, make sure you check which type of module you need. Below is a list of the most common modules in use today.
- Standard H200 Module
- ProBead Self-Cleaning Module
- Reduced Cavity H200 Module
- Zero Cavity Micro Adjust H200 Module
- Swirl Pattern Modules
- Weave Pattern Modules
- H20 Modules
If you have any questions on which items you may need, please reach out to a sales representative by either calling (561) 272-5442 or emailing sales@ussefl.com. We manufacture all products in the United States and are here to offer the best price possible to get your packaging line up and running as quickly as possible.